Accessories

available accessories

We have a large selection of ventilation accessories including flexible ducting, insulated ducting, vents, grilles, controllers, remotes and plugs. If you are looking for accessories for a particular fan you wish to purchase from us, we have compiled a list of recommended accessories that go with each product which can be found at the bottom of most product pages.

You can use the category buttons below to narrow down your search for exhaust fan accessories. Alternatively all products are listed below the buttons (you can further narrow your search using the options available on the left sidebar).

Please be aware that some accessories will require installation by a qualified electrician, even if you are purchasing them to use in conjunction with a fan  which is otherwise suitable for a DIY install (has a lead and plug).

exhaust fan ventsvent and ducting kits
flexible ducting for exhaust fansbackdraft shutters for exhaust fan systems
joiners and reducers for inline exhaust systemsjunctions and bto's for exhaust fan systems
roof mounted roof cowl kitsother accessories for exhaust systems
rangehood duct kitsfloor vents

View cart “Variable 1-25 Minute Timer for Axial Exhaust Fans – Electrician Required” has been added to your cart.
Display:  List Grid

Showing 1–24 of 33 results

  • This is an electronic type speed-controller which provides infinite variation of fan speed from 100% down to approximately 30% of full speed.
    When used to control a number of identical fans the sum of the full load amps of all the connected fans must not exceed 85% of the maximum rating of the controller (which is 2.0).
    Dimensions: 70W × 114H × 36D

    $95.00
  • Dimensions 110 x 80 x 42 (mm)

    The R10 Speed Controller is a variable speed switch specifically designed to be used with selected Expella fans. It’s design features a cover, removable terminals for easy connection and an external trimmer for adjusting the fans minimum operational speed.

    Features

    • Preset holes for surface and recessed cable entry
    • Single-phase 230V – 50Hz
    • Max. Load 1A
    • IP42 Protected

    $99.00
  • Add this product to your shopping cart if you wish for us to install a flex and plug to your fan. The cord on this plug in 30cm in length. This is for use with the Commercial wall fans ONLY.

    Please Note: We are unable to accept returned fans that have a flex and plug installed.

     

    Note: This lead and plug option can only be used in conjunction with specific fans – Please refer to compatible accessories below product listings.

    $15.00
  • The tradies choice mechanical damper has a 200mm diameter barrel with 5mm silver foam insulation. The barrel has a mechanical actuator on the side which will mechanically open/close the damper once it has been wired to a on/off switch. Perfect for heat transfer kits and other applications which may require a mechanical damper.

    $89.00
  • The tradies choice mechanical damper has a 150mm diameter barrel with 5mm silver foam insulation. The barrel has a mechanical actuator on the side which will mechanically open/close the damper once it has been wired to a on/off switch. Perfect for heat transfer kits and other applications which may require a mechanical damper.

    $79.00
  • Dimensions: 120 x 120 x 43mm

    A non-reversible variable electronic speed controller. Maximum load 450w.
    220 – 240v 50Hz.

    $139.00
  • Ceiling kit made of soft rubber to prevent water infiltration and to maintain IPX4 protection on all surfaces.

    $29.00
  • Ceiling kit made of soft rubber to prevent water infiltration and to maintain IPX4 protection on all surfaces.

    $25.00
  • Ceiling kit made of soft rubber to prevent water infiltration and to maintain IPX4 protection on all surfaces.

    $20.00
  • Metal damper with additional 240v actuator.

    This mechanical shutter is perfect for zoning requirements for a heat transfer system. Its 240v so would require an electrician to wire the damper to a switch. This will give you the ability to open/close the damper as and when required. This is particularly useful if you wish to shut off a branch of a heat transfer kit (eg if its a spare bedroom seldom used for example).

    This kit consists of a 250mm metal zone damper and 240v actuator – read the 'installation example' tab below for more information and example diagram.

    This is a single room option only – multiple room zoning requires more components and would incur a consultancy fee for us to put together the necessary kit. If you are interested in this please contact us.

    Please Note: Picture is for illustrative purposes only.

    $165.00
  • Metal damper with additional 240v actuator.
     
    This mechanical shutter is perfect for zoning requirements for a heat transfer system. Its 240v so would require an electrician to wire the damper to a switch. This will give you the ability to open/close the damper as and when required. This is particularly useful if you wish to shut off a branch of a heat transfer kit (eg if its a spare bedroom seldom used for example).
     
    This kit consists of a 150mm metal zone damper and 240v actuator.
     
    This is a single room option only – multiple room zoning requires more components and would incur a consultancy fee for us to put together the necessary kit. If you are interested in this please contact us.
     
    Please Note: Picture is for illustrative purposes only.

    $120.00
  • 3 steps reversible speed controller for use with the Vitro range of exhaust fans (fitted with transformer).
    • ON/OFF switch
    • IP42 protection
    • Max. load: 100 W (0,5 A)
    • Supply voltage: 230V-50/60 Hz
    • Sizes: 118 x 118 x 58 mm
    • Weight: 0,7 kg

    Installation would need to be carried out by a qualified electrician.

    $89.00
  • The wall mounted Humidity Sensor automatically activates the exhaust fan when humidity levels reach a pre- determined level, reducing moisture in the home and helping to prevent condensation and mould.

    $119.00
  • The Deflecto Lint Trap Kit is for indoor dryer venting. It involves quick and easy installation fitting all clothes dryers however cannot be used with gas clothes dryers. Included in the kit is the lint trap, Supurr-Flex Metallic Duct and 2 Clamps. This particular venting kit is for indoor use only.



    Performance Notes:

    • Melting Point: 325°F+ for container.
    • Operating Temperature: 265°F for duct.
    • May require open doors in small rooms for adequate heat distribution.

    Please Note: An electrician will be required to install this product
    spec sheet

    $49.00
  • The Ventair Motion Sensor and Timer operates with all new and exisiting Ventair exhaust fans. The motion sensor component uses high quality infrared technology to detect signals of someone entering an area of up to 5 meters. The run on timer will work for 1 to 20 minutes of time before switching off.

    $49.00
  • The Variable Timer runs for approximately 1-25 minutes (can be adjusted) after switching off, to clear steam and odour once you leave the room.

     

    Features:
    Input: AC230-240V ~ 50Hz
    Maximum Load: 500 Watts
    Operation Temperature: -10°C to 40°C
    Settings: Adjustable from 1 to 25 minutes
    Warranty: 12 months replacement

    Please Note: An electrician will be required to install this product

    5.00 out of 5
    $39.00
  • Mounting: The sensors are designed for indoor wall surface installation.

    This Run on Timer enables the fan operation within the set time period after pressing the knob for switching the fan OFF. After the set time from 2 to 30 minutes the fan switches automatically OFF. The run-out timer is generally applicable for the fans installed in bathrooms, WC or kitchens.

    $65.00
  • spec sheet

    The Alphalux 180 Degree Motion Sensor will allow you to have motion triggered lighting or act as a safety and security precaution.

    Time Control

    Adjustments can be made to the length of time the sensor remains on after being triggered. This can vary from a minimum of 5 seconds to a maximum of 7 minutes depending on what is preferred in a particular location. Once adjusted it will have an immediate effect. Adjustments during the ON cycle should be avoided.

    Lux Control

    This feature will help to determine at what level of background light the unit will function. For example if dial is moved to the sun position the unit will trigger under full daylight conditions and at the moon then it will only trigger in complete darkness. Therefore, if three quarters between the sun and moon then triggering will occur at dusk.
    Initial setup should be done at the time of day you require your lights to illuminate to ensure trigger accuracy to preferred light level.

    Distance Control

    This function enables control over the distance at which the unit will detect movement. Range available to user is a maximum of 10 metres and a minimum of 1 metre.

    Finding an ideal location will assist you in avoiding nuisance triggering. This includes not mounting it close to electrical devices, fluorescent fittings, remote control operated doors, reflective surfaces.
    Unit should be a minimum of 2.4 metres above monitored area for best performance and to minimise false triggering of most animals direct above their expected height.

    This product must be installed by a qualified electrician and in accordance with appropriate wiring rules and regulations.

    $59.00
  • A simple plug in 24 hour timer, allowing you to specify desired operation time.
     
    Timer Instructions – To Set the Timer:

    1. Push down segments between desired ‘ON’ and ‘OFF’ times.
    2. One segment represents 15 minutes of ‘ON’ time.
    3. Rotate dial to align present time with pointer.
    4. Insert into powerpoint and switch on.
    5. To override programme, switch to ‘I’.

    240v AC 50Hz
    10A 2400W Max

    4.50 out of 5
    $15.00
  • A two position switch designed for use with the TT Mixflow Inline fan or VKP Minibox.

    The speed controller is used for speed switching of domestic fans which have multispeed motors.

    If using this product with an exhaust fan that comes with a lead and plug, please consult your electrician. In most cases the lead and plug will need to be removed from the fan in order to use this switch. 

    Dimensions of switch plate: L= 88mm x W= 88mm

    5.00 out of 5
    $49.00 $45.00
  • Type: RF (Radio Frequency)
    Range: Up to 30m

    Martec’s RF (Radio Frequency) Bathroom Heater LCD Remote Control suits all Martec Bathroom Heater 3 in 1’s. Able to be fitted as an after market Remote you can change from a standard wall switch to LCD remote option very easily.

    The Martec premium Bathroom Heater LCD Remote Control is both stylish and of course of the highest quality, featuring Full or Half Heat option (4 Heat Models Only, 2 Heat Models is Full Heat Only), Light On/Off, Exhaust Fan On/Off and a handy All Off function for turning everything off when leaving the bathroom with a single press of a button. It also has a 30 metre RF operational range, and makes installation so much easier for the electrician.

    Features

    • Adapts To All Martec Bathroom Heaters
    • Easy To Use LCD Display
    • Full or Half Heat Function
    • Includes Wall Mounting Bracket and 9 Volt Battery
    • 4 Seperate Frequency Switches (allows multiple remote units in 1 house)
    • Light On and Off Button
    • Exhaust Fan On and Off
    • Handy All Off Button

    4.00 out of 5
    $90.50
  • The metal worm clamps are designed for fixing ductwork to inline motors. Clamps are a good substitute for traditional duct tape that may loose it's hold over time. Packs of two.

    $12.00
  • The metal worm clamps are designed for fixing ductwork to inline motors. Clamps are a good substitute for traditional duct tape that may loose it's hold over time. Packs of two.

    $10.00
  • The metal worm clamps are designed for fixing ductwork to inline motors. Clamps are a good substitute for traditional duct tape that may loose it's hold over time. Packs of two.

    $9.00