Timers & Speed Controls

Display:  List Grid

  • This is an electronic type speed-controller which provides infinite variation of fan speed from 100% down to approximately 30% of full speed.
    When used to control a number of identical fans the sum of the full load amps of all the connected fans must not exceed 85% of the maximum rating of the controller (which is 2.0).
    Dimensions: 70W × 114H × 36D

  • Dimensions 110 x 80 x 42 (mm)

    The R10 Speed Controller is a variable speed switch specifically designed to be used with selected Expella fans. It’s design features a cover, removable terminals for easy connection and an external trimmer for adjusting the fans minimum operational speed.


    • Preset holes for surface and recessed cable entry
    • Single-phase 230V – 50Hz
    • Max. Load 1A
    • IP42 Protected

  • Dimensions: 120 x 120 x 43mm

    A non-reversible variable electronic speed controller. Maximum load 450w.
    220 – 240v 50Hz.

  • 3 steps reversible speed controller for use with the Vitro range of exhaust fans (fitted with transformer).
    • ON/OFF switch
    • IP42 protection
    • Max. load: 100 W (0,5 A)
    • Supply voltage: 230V-50/60 Hz
    • Sizes: 118 x 118 x 58 mm
    • Weight: 0,7 kg

    Installation would need to be carried out by a qualified electrician.

  • The wall mounted Humidity Sensor automatically activates the exhaust fan when humidity levels reach a pre- determined level, reducing moisture in the home and helping to prevent condensation and mould.

  • The Ventair Motion Sensor and Timer operates with all new and exisiting Ventair exhaust fans. The motion sensor component uses high quality infrared technology to detect signals of someone entering an area of up to 5 meters. The run on timer will work for 1 to 20 minutes of time before switching off.

  • The Variable Timer runs for approximately 1-25 minutes (can be adjusted) after switching off, to clear steam and odour once you leave the room.


    Input: AC230-240V ~ 50Hz
    Maximum Load: 500 Watts
    Operation Temperature: -10°C to 40°C
    Settings: Adjustable from 1 to 25 minutes
    Warranty: 12 months replacement

    Please Note: An electrician will be required to install this product

    5.00 out of 5
  • Mounting: The sensors are designed for indoor wall surface installation.

    This Run on Timer enables the fan operation within the set time period after pressing the knob for switching the fan OFF. After the set time from 2 to 30 minutes the fan switches automatically OFF. The run-out timer is generally applicable for the fans installed in bathrooms, WC or kitchens.

  • A simple plug in 24 hour timer, allowing you to specify desired operation time.
    Timer Instructions – To Set the Timer:

    1. Push down segments between desired ‘ON’ and ‘OFF’ times.
    2. One segment represents 15 minutes of ‘ON’ time.
    3. Rotate dial to align present time with pointer.
    4. Insert into powerpoint and switch on.
    5. To override programme, switch to ‘I’.

    240v AC 50Hz
    10A 2400W Max

    4.50 out of 5
  • A two position switch designed for use with the TT Mixflow Inline fan or VKP Minibox.

    The speed controller is used for speed switching of domestic fans which have multispeed motors.

    If using this product with an exhaust fan that comes with a lead and plug, please consult your electrician. In most cases the lead and plug will need to be removed from the fan in order to use this switch. 

    Dimensions of switch plate: L= 88mm x W= 88mm

    5.00 out of 5
    $49.00 $45.00
  • A flush built in mounted uint box for use with the VKM variable speed controller.

  • A surface mounted junction box for use with the VKM variable speed controller.

    5.00 out of 5
  • The Speed controller is used for smooth speed control of domestic fans.

    Basic Technical Specification

    • Output power, not more than 500w (load current not more than 2.0a)
    • Weight, not more than 0.11kg
    • IP40 Rated
    4.00 out of 5